Can I Install a Bath Tub Myself? Considerations And Actions
Can I Install a Bath Tub Myself? Considerations And Actions
Blog Article
This great article listed below about Installing A Bathtub is exceptionally attention-grabbing. Check it out yourself and figure out what you think about it.
Setting up a bath tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a new one is also a moderately tough project. If the old tub is easily obtainable, the project can move easily; if you need to open up a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task and also fit attempting it. Rather than hiring a professional to take control of a halfway-completed project, it is much better to take into consideration using one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This short article will help you install a brand-new bathtub in your bathroom if you have already purchased a new tub and don't need to alter the plan of your previous water system pipelines.
Your devices as well as product list ought to make up the following:
Preparing for the Installation
Firstly, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be quite troublesome because of the limited gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning during this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, position the bathtub in the needed position. The wood boards are handy in evenly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level and adjusting the feet on the bath tub until the spirit level reads degree.
To install taps, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water and inspect all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub needs to wait until the bathtub has actually been used a minimum of when as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making certain that the washers are in area in between the tap and the sink. Secure the tap in place with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a stiff seal, creating the water to penetrate the wall between the bath and also the tiling, bring about issues with moisture and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealant can crack rather early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that review on Installing A Bathtub while doing a lookup on the search engines. Those who appreciated our post please be sure to pass it around. Thanks a bunch for your time. Come back soon.
Schedule Your Service
Report this page